Journal of Shandong University(Engineering Science) ›› 2019, Vol. 49 ›› Issue (4): 99-107.doi: 10.6040/j.issn.1672-3961.0.2019.018

• Mechanical, Energy and Power Engineering • Previous Articles     Next Articles

Phase change characteristics of paraffin in rectangular storage unit

Huilin ZHOU(),Yan QIU*()   

  1. School of Energy and Power Engineering, Shandong University, Jinan 250061, Shandong, China
  • Received:2019-01-12 Online:2019-08-20 Published:2019-08-06
  • Contact: Yan QIU E-mail:201734101@mail.sdu.edu.cn;anneqiu@sdu.edu.cn
  • Supported by:
    国家自然科学基金资助项目(51576115);国网山东省电力公司科技资助项目(52060616000L)

RichHTML

15

PDF (PC)

1047

Abstract:

To study the heat transfer characteristics of phase change material (PCM) in a storage unit and improve the heat transfer efficiency of phase change heat exchanger, the enthalpy-porous media model and FLUENT program were used to carry out a numerical investigation on the heat transfer process of paraffin in a rectangular heat storage unit. The element liquid fraction β and dimensionless Fo, Ste and Ra were introduced to analyze the influences of different positions outside the tube and inlet temperatures of heat transfer fluid on the melting and solidification process of paraffin. The results showed that the paraffin outside the tube was melted in order from the upper to the left/right part, then the lower part. The total melting time of paraffin in upper part was shorten by at least 20% compared with other parts. Conversely, in the heat release process, the paraffin was solidified in order from the lower, the left/right part and the upper part. The heat transfer mechanism in the unit changed gradually from heat conduction to natural convection in the thermal storage process. The efficiency of heat storage and release could be improved significantly by increasing the temperature difference between heat transfer fluid and paraffin. The criterion of β was obtained by polynomial fitting.

Key words: phase change heat exchanger, PCM, thermal storage, thermal release, numerical simulation

CLC Number: 

  • TK124

Fig.1

Physical model"

Table 1

Physical properties of paraffin"

相变温度/K相变潜热/(kJ·kg-1)密度/(kg·m-3)热导率/(W·(m·K)-1)比热容/(kJ·(kg·K)-1)
固态液态固态液态固态液态
319.68141.919167760.270.111.72.5

Fig.2

Mesh of calculation region"

Fig.3

Distribution of 1#~16# temperature metrical points"

Fig.4

Comparison between numerical simulation and experimental results"

Fig.5

Average Nusselt number Vs. Fourier number during melting"

Fig.6

Paraffin wax temperature Vs. melting time"

Fig.7

Effect of different inlet temperature on paraffin wax′s endothermal temperature"

Fig.8

Effect of different inlet temperature on paraffin wax′s liquid fraction"

Fig.9

Melting fraction changes with X(X=Ste·Fo·Ra0.05)"

Fig.10

Paraffin′s exothermal temperature Vs. soliding time"

Fig.11

Effect of different inlet temperature on paraffin wax's exothermal temperature"

Fig.12

Effect of different time and inlet temperature on paraffin wax's liquid fraction"

1 徐治国, 赵长颖, 纪育楠. 中低温相变蓄热的研究进展[J]. 储能科学与技术, 2014, 3 (3): 179- 190.
doi: 10.3969/j.issn.2095-4239.2014.03.02
XU Zhiguo , ZHAO Changying , JI Yunan . State-of-the-art of phase-change thermal storage at middle-low temperature[J]. Energy Storage and Technology, 2014, 3 (3): 179- 190.
doi: 10.3969/j.issn.2095-4239.2014.03.02
2 毛发, 章学来, 丁磊, 等. 热管式相变储能系统蓄/放热性能试验[J]. 热力发电, 2016, 45 (11): 48- 53.
doi: 10.3969/j.issn.1002-3364.2016.11.048
MAO Fa , ZHANG Xuelai , DING Lei , et al. Experimental research on heat charging and discharging performance of heat pipe phase change energy storage system[J]. Thermal Power Generation, 2016, 45 (11): 48- 53.
doi: 10.3969/j.issn.1002-3364.2016.11.048
3 宋香娥. 太阳能发电热管吸热器相变蓄热单元性能分析[J]. 热力发电, 2015, 44 (9): 37- 42.
doi: 10.3969/j.issn.1002-3364.2015.09.037
SONG Xiang'e . Performance analysis of phase change heat storage unit in heat pipe receiver of solar power generation systems[J]. Thermal Power Generation, 2015, 44 (9): 37- 42.
doi: 10.3969/j.issn.1002-3364.2015.09.037
4 孟锋, 安青松, 郭孝峰, 等. 蓄热过程强化技术的应用研究进展[J]. 化工进展, 2016, 35 (5): 1273- 1281.
MENG Feng , AN Qingsong , GUO Xiaofeng , et al. Research progress in application of heat storage enhancement technology[J]. Chemical Industry and Engineering Progress, 2016, 35 (5): 1273- 1281.
5 杨佳霖, 杜小泽, 杨立军, 等. 泡沫金属强化石蜡相变蓄热过程可视化实验[J]. 化工学报, 2015, (2): 497- 503.
YANG Jialin , DU Xiaoze , YANG Lijun , et al. Visualized experiment on dynamic thermal behavior of phase change material in metal foam[J]. CIESC Journal, 2015, (2): 497- 503.
6 SARI A , KARAIPEKLI A . Thermal conductivity and latent heat thermal energy storage characteristics of paraffin/expanded graphite composite as phase change material[J]. Applied Thermal Engineering, 2007, 27 (8): 1271- 1277.
7 MILLS A , FARID M , SELMAN J R , et al. Thermal conductivity enhancement of phase change materials using a graphite matrix[J]. Applied Thermal Engineering, 2006, 26 (14): 1652- 1661.
8 吴志根, 赵长颖, 顾清之. 多孔介质在高温相变蓄热中的强化换热[J]. 化工学报, 2012, 63 (增刊1): 119- 122.
WU Zhigen , ZHAO Changying , GU Qingzhi . Heat transfer enhancement of high temperature thermal energy storage using porous materials[J]. CIESC Journal, 2012, 63 (Suppl. 1): 119- 122.
9 DARKWA J , SU O . Thermal simulation of composite high conductivity laminated microencapsulated phase change material (MEPCM) board[J]. Applied Energy, 2012, 95 (2): 246- 252.
10 FOURIE J G , PLESSIS J P D . Pressure drop modelling in cellular metallic foams[J]. Chemical Engineering Science, 2002, 57 (14): 2781- 2789.
doi: 10.1016/S0009-2509(02)00166-5
11 DARZI A A R , FARHADI M , SEDIGHI K . Numerical study of melting inside concentric and eccentric horizontal annulus[J]. Applied Mathematical Modelling, 2012, 36 (9): 4080- 4086.
doi: 10.1016/j.apm.2011.11.033
12 崔海亭, 周慧涛, 蒋静智. 用于储存太阳能的相变蓄热器蓄热性能研究[J]. 可再生能源, 2013, 31 (12): 17- 20.
doi: 10.3969/j.issn.1671-5292.2013.12.004
CUI Haiting , ZHOU Huitao , JIANG Jingzhi . Numerical simulation on heat storing performances of phase-change thermal storage for solar energy[J]. Renewable Energy, 2013, 31 (12): 17- 20.
doi: 10.3969/j.issn.1671-5292.2013.12.004
13 晋瑞芳, 付海明, 徐芳, 等. 同心套管式相变蓄热装置凝固过程的数值模拟[J]. 建筑热能通风空调, 2009, 28 (1): 14- 17.
doi: 10.3969/j.issn.1003-0344.2009.01.004
JIN Ruifang , FU Haiming , XU Fang , et al. Numerical simulation of discharging process for a shell-tube phase change thermal storage[J]. Building Energy & Environment, 2009, 28 (1): 14- 17.
doi: 10.3969/j.issn.1003-0344.2009.01.004
14 彭冬华, 陈振乾, 施明恒. 泡沫金属内相变材料融化传热过程的数值模拟[J]. 工程热物理学报, 2009, 30 (6): 1025- 1028.
doi: 10.3321/j.issn:0253-231X.2009.06.034
PENG Donghua , CHEN Zhenqian , SHI Mingheng . Numerical simulation of phase change material thawing process in metallic foams[J]. Journal of Engineering Thermophysics, 2009, 30 (6): 1025- 1028.
doi: 10.3321/j.issn:0253-231X.2009.06.034
15 KAZEMI M , HOSSEINI M J , RANJBAR A A , et al. Improvement of longitudinal fins configuration in latent heat storage systems[J]. Renewable Energy, 2018, 116, 447- 457.
doi: 10.1016/j.renene.2017.10.006
16 WANG Y , AMIRI A , VAFAI K . An experimental investigation of the melting process in a rectangular enclosure[J]. International Journal of Heat & Mass Transfer, 1999, 42 (19): 3659- 3672.
17 CHANG J , LEUNG D Y C , WU C Z , et al. A review on the energy production, consumption, and prospect of renewable energy in China[J]. Renewable & Sustainable Energy Reviews, 2003, 7 (5): 453- 468.
18 郭英利.石蜡圆管外相变蓄热与释热规律的研究[D].天津:天津大学, 2008.
GUO Yingli. Study on the heat storage and heat release by paraffin phase change outside the pipe[D]. Tianjin: Tianjin University, 2008.
19 袁艳平, 曹晓玲, 白力, 等. 矩形单元内癸酸熔化特性的数值模拟与实验[J]. 西南交通大学学报, 2012, 47 (2): 236- 240.
YUAN Yanping , CAO Xiaoling , BAI Li , et al. Melting behaviors of capric acid in rectangular enclosure[J]. Journal of Southwest Jiao Tong University, 2012, 47 (2): 236- 240.
20 SHATIKIAN V , ZISKIND G , LETAN R . Numerical investigation of a PCM-based heat sink with internal fins[J]. International Journal of Heat & Mass Transfer, 2005, 48 (17): 3689- 3706.
[1] Mingcai LIU. Impact analysis on construction of large section and small spacing road tunnel [J]. Journal of Shandong University(Engineering Science), 2019, 49(4): 78-85.
[2] Yulei ZHANG,Yong WANG,Yudong XIE,Guang SUN,Yanyun WANG,Jiazhen HAN. Numerical simulation on kinetics characteristics of liquid metal MHD generator [J]. Journal of Shandong University(Engineering Science), 2019, 49(1): 101-106.
[3] SONG Guijie. Deformation characteristic and instability analysis for shallow soft rock section during tunnel-entering construction [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2018, 48(2): 53-60.
[4] WANG Danhua, ZHANG Guanmin, LENG Xueli, XU Mengna, HAN Yuanyuan. The numerical simulation of two-phase flow distribution characteristics in T-tube [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2018, 48(1): 89-95.
[5] XIA Mengran, LI Wei, FENG Xiao, ZHU Guangxuan, LI Xia. Grouting reinforcement and excavation stability on super-shallow buried and water-rich sand stratum subway transverse channel [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2017, 47(2): 47-54.
[6] LYU Guoren, ZHANG Qun, NIU Ben, GAO Quanting, WU Zhaoshou. The effects of pile foundation of high-rise building on adjacent structures [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2017, 47(1): 48-58.
[7] PENG Yuancheng, DONG Xu, LIANG Na, DENG Zhenquan. Model test of the Beipan River's new open-web continuous rigid frame bridge corner node [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2016, 46(6): 113-119.
[8] MI Chunrong, LI Jianming. Development and application of after grouting device for prestressed concrete pipe pile [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2016, 46(4): 89-95.
[9] TANG Weize, OU Jinqiu, CUI Xinzhuang, LOU Junjie, XIAO Ming, ZHANG Jiong, HUANG Dan, HOU Fei. Field test and research on vehicle load induced dynamic pore pressure in asphalt pavement [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2015, 45(6): 84-90.
[10] CAO Weidong, DAI Tao, YU Jinbiao, XI Kaihua, LU Tongchao, CHENG Aijie. An IMPIMC method for chemical simulation [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2015, 45(1): 88-94.
[11] GAO Zhijun, CUI Xinzhuang, SUI Wei, GUO Hong, LIU Hang, LI Changyi, FENG Hongbo. Dynamic interaction and damage analysis of large runaway vehicle and tunnel lining [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2014, 44(5): 49-57.
[12] ZHANG Tao, HAN Jitian, YAN Suying, YU Zeting, ZHOU Ran. The analysis and testing of thermal performance on solar evacuated tube [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2014, 44(4): 76-83.
[13] ZHOU Qian, ZHAO Degang. Application of the horizontal jet grouting pile in water-bearing sandy layer of shallow excavating tunnel [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2014, 44(4): 52-57.
[14] ZHANG Wenjun, LI Shucai, SU Maoxin*, XUE Yiguo, QIU Daohong. Detection  method of karst caves in city subway based on  the cross-hole resistivity tomography [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2014, 44(3): 75-82.
[15] LIU Yang, GE Lian-sheng*. TE mode analysis based on a new Padé approximant BPM algrorithm [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2014, 44(1): 19-23.
Viewed
Full text


Abstract

Cited
  Shared   
  Discussed   
[1] LI Liang, LUO Qiming, CHEN Enhong. Graph-based ranking model for object-level search
[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2009, 39(1): 15 -21 .
[2] CHEN Rui, LI Hongwei, TIAN Jing. The relationship between the number of magnetic poles and the bearing capacity of radial magnetic bearing[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2018, 48(2): 81 -85 .
[3] LIU Wen-liang, ZHU Wei-hong, CHEN Di, ZHANG Hong-quan. Detection and tracking of moving targets using the morphology match in radar images[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2010, 40(3): 31 -36 .
[4] ZHANG Ying,LANG Yongmei,ZHAO Yuxiao,ZHANG Jianda,QIAO Peng,LI Shanping . Research on technique of aerobic granular sludge cultivationby seeding EGSB anaerobic granular sludge[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2006, 36(4): 56 -59 .
[5] Yue Khing Toh1， XIAO Wendong2， XIE Lihua1. Wireless sensor network for distributed target tracking: practices via real test bed development[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2009, 39(1): 50 -56 .
[6] LIU Xin 1, SONG Sili 1, WANG Xinhong 2. [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2009, 39(2): 98 -100 .
[7] . [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2009, 39(2): 104 -107 .
[8] WANG Shan,LI Tian-ze . A new method for the control of a wound-rotor induction machine[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2008, 38(3): 86 -89 .
[9] . [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2009, 39(2): 131 -136 .
[10] LIANG Jing-yun,WANG Ming-gang,CHAI Jia-qian,LIU yong-qing . Synthesis and in vitro antibacterial activity of 1,6-Di-(N5-phenyl-N1-diguanido) hexane dihydrochloride[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2008, 38(3): 104 -107 .
Copyright 2018 © Editorial office of Journal of Shandong University (Engineering Science)
Supported by Beijing Magtech Co.Ltd