Journal of Shandong University(Engineering Science) ›› 2019, Vol. 49 ›› Issue (3): 103-107.doi: 10.6040/j.issn.1672-3961.0.2018.100

• Mechanical Engineering • Previous Articles     Next Articles

Experimental study on prestressed process parameters of diamond circular saw roll tensioning

Xiaotao CHEN1,2,3(),Jinsheng ZHANG1,2,3,4,*(),Bo HUANG1,2,3,Junwei JU1,2,3,Bainian ZHANG1,2,3,Jiaqi ZHAO1,2,3   

  1. 1. School of Mechanical Engineering, Shandong University, Jinan 250061, Shandong, China
    2. Stone Engineering Technology Research Center of Shandong Province, Jinan 250061, Shandong, China
    3. Key Laboratory of High-Efficiency and Clean Mechanical Manufacture of Ministry of Education, Shandong University, Jinan 250061, Shandong, China
    4. Haiyi Group Institute, Shandong University, Rizhao 276800, Shandong, China
  • Received:2018-03-09 Online:2019-06-20 Published:2019-06-27
  • Contact: Jinsheng ZHANG E-mail:569764256@qq.com;zhangjs@sdu.edu.cn
  • Supported by:
    山东省泰山产业领军人才工程传统产业创新类项目(tscy20150228)

Abstract:

Typical Φ1 650 mm diamond circular saw blade was pretreated by prestressing. The axial deformation of saw blade substrate before and after prestressing treatment was collected to study the effect of prestressing position and load on tensile state. The test results showed that the position of prestress was positively related to the radial distance, and the effect of tangential tensile stress was more obvious. The axial rigidity and stability of saw blades was enhanced, and the ability of saw blade steel core to restrain the axial load-bearing deformation was enhanced by 216%~232%. The prestressing load increased the ability of the circular saw blade to suppress deformation. If the prestressing load was too large, the overall rigidity and stability of the saw blade after the prestressing treatment weakened, and the ability of the matrix to suppress the axial load deformation only increased by 155%~187%.

Key words: circular saw blade, prestress treatment, rolling, technological parameter, axial deformation

CLC Number: 

  • TB553

Fig.1

Prestressed roll pressure and detection system of circular saw blade"

Table 1

Parameters of the circular saw blade material"

密度/(kg·m-3) 弹性模量E/GPa 泊松比μ
7 800 316 0.3

Table 2

Structure size parameters of circular saw blade"

基体外圆直径Φ/mm 基体厚度/mm 齿数
1 650 6.8 108

Fig.2

Φ 1 650 mm circular saw blade base rolled product"

Fig.3

Detection method of axial loading deformation of circular saw blade"

Fig.4

Curves of prestress position parameters influence on axial deformation curve"

Fig.5

Three node deformation data of circular saw blade"

1 TIAN J F , HUTTON S G . Cutting-induced vibration in circular saws[J]. Journal of Sound & Vibration, 2001, 242 (5): 907- 922.
2 白硕玮, 张进生, 王长会, 等. 薄型锯片锯切硬脆石材横向振动模型[J]. 农业机械学报, 2015, 46 (2): 372- 378.
BAI Shuowei , ZHANG Jinshen , WANG Changhui , et al. Analytical model of transverse vibration of thin type circular saw in sawing hard and brittle stone[J]. Transactions of the Chinese Society of Agricultural Machinery, 2015, 46 (2): 372- 378.
3 徐西鹏. 岩石材料的金刚石锯切研究进展[J]. 机械工程学报, 2003, 39 (9): 17- 22.
doi: 10.3321/j.issn:0577-6686.2003.09.003
XU Xipeng . Advances in the research of diamond stone sawing[J]. Journal of Mechanical Engineering, 2003, 39 (9): 17- 22.
doi: 10.3321/j.issn:0577-6686.2003.09.003
4 TöNSHOFF H K , SCHERGER A . About damping mechanisms for disk shaped tools[J]. CIRP Annals-Manufacturing Technology, 1981, 30 (1): 305- 309.
doi: 10.1016/S0007-8506(07)60947-0
5 LI S , WANG C , ZHENG L , et al. Dynamic stability of cemented carbide circular saw blades for woodcutting[J]. Journal of Materials Processing Tech, 2016, 238, 108- 123.
doi: 10.1016/j.jmatprotec.2016.07.018
6 JR C D M , NIEH L T . Control of circular-disk stability with membrane stresses[J]. Experimental Mechanics, 1971, 11 (11): 490- 498.
doi: 10.1007/BF02327688
7 张秀伟.金刚石圆锯片应力场数学模型的建立及求解[D].大连:大连理工大学, 2000.
8 武松灵.圆锯片的辊压适张机理及其工艺研究[D].北京:北京科技大学, 2017.
WU Songling. Study on the roll tensioning technology and mechanism of circualr saw blade[D]. Beijing: University of Science and Technology Beijing, 2017.
9 杨庆斌, 李远, 郭桦, 等. 金刚石圆锯片横向变形控制的实验初探[J]. 金刚石与磨料磨具工程, 2011, 31 (5): 39- 43.
doi: 10.3969/j.issn.1006-852X.2011.05.009
YANG Qingbin , LI Yuan , GUO Hua. , et al. Research on the lateral vibration and deformation control of diamond circular sawblade[J]. Diamond and Abrasives Engineering, 2011, 31 (5): 39- 43.
doi: 10.3969/j.issn.1006-852X.2011.05.009
10 房怀英, 李远, 徐西鹏. 圆锯片轴向变形的解析模型及其实验验证[J]. 华侨大学学报(自然科学版), 2012, 33 (4): 361- 365.
FANG Huaiying , LI Yuan , XU Xipeng . Analytical model and experimental verification on axial deformation of circular saw in sawing of stone[J]. Journal of Huaqiao University(Natural Science), 2012, 33 (4): 361- 365.
11 苏成功, 刘燕, 王威强, 等. 压痕对不锈钢材料表面残余应力的影响[J]. 山东大学学报(工学版), 2017, 47 (1): 90- 96.
SU Chenggong , LIU Yan , WANG Weiqiang , et al. The influence of indentation on the surface residual stress of stainless steel[J]. Journal of Shandong University (Engineering Science), 2017, 47 (1): 90- 96.
12 SA Chao , XI Baotian , Li L . An Approach to detecting tension of a circular saw[J]. Forestry Studies in China, 1999, 1 (2): 64- 70.
13 KOSTRYKIN V , SCHRADER R . Kirchhoff's rule for quantum wires[J]. Journal of Physics A: General Physics, 1998, 32 (4): 595- 630.
14 王杨, 撒潮, 陈永光, 等. 微机控制圆锯片应力检测系统的设计[J]. 木材加工机械, 2004, 15 (2): 6- 9.
doi: 10.3969/j.issn.1001-036X.2004.02.002
WANG Yang , SA Chao , CHEN Yongguang , et al. The design of microcomputer control system of detecting circualr saw blade[J]. Wood Processing Machinery, 2004, 15 (2): 6- 9.
doi: 10.3969/j.issn.1001-036X.2004.02.002
15 张明松, 王勇, 李鹏. 圆锯片切线辊压适张处理的残余应力分析以及辊压参数优化[J]. 三峡大学学报(自然科学版), 2017, 39 (1): 93- 97.
ZHANG Mingsong , WANG Yong , LI Peng . Anlysis of residual stress of circular saw blade after tangent roll tensioning and optimization of rolling parameter[J]. Journal of China Three Gorges University (Natural Sciences), 2017, 39 (1): 93- 97.
16 吴恩启, 兴磊磊, 吴绍民, 等. 基于曲线拟合的圆锯片变形检测算法[J]. 光电工程, 2015, 42 (8): 8- 13.
doi: 10.3969/j.issn.1003-501X.2015.08.002
WU Enqi , XING Leilei , WU Shaomin , et al. Detecting algorithm of circular saw blade deformation based on curve fitting[J]. Opto-Electronic Engineering, 2015, 42 (8): 8- 13.
doi: 10.3969/j.issn.1003-501X.2015.08.002
[1] Jiachen WANG,Xianghong TANG,Jianguang LU. Research onfeature selection technology in bearing fault diagnosis [J]. Journal of Shandong University(Engineering Science), 2019, 49(2): 80-87, 95.
[2] WANG Fei, XU Jian, LI Wei, WANG Xinhao, SHI Xiaohan. Rolling optimal dispatch method of wind power based on distributed energy storage system [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2017, 47(6): 89-94.
[3] GAO Xue-ping, ZHU Bo, YU Kuan. Computer controlling and performance testing of  a fluidized pre-oxidation furnace for carbon fiber manufacture [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2010, 40(4): 80-83.
[4] ZHANG Guang-Xian. Advanced geological prediction of filled caverns and  control of geological disasters [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2009, 39(4): 78-81.
[5] DONG Rui-hua, LI Mu-sen, WANG Xiu-chun, SUN Xi-tai. Action of rolling on mechanical energy aided aluminizing progresses [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2008, 38(6): 91-94.
[6] LI Cai-hong,LI Yi-bin,FAN Chen . Dynamic obstacle avoidance Algorithm for the mobile robot [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2007, 37(5): 60-64 .
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
[1] CHEN Rui, LI Hongwei, TIAN Jing. The relationship between the number of magnetic poles and the bearing capacity of radial magnetic bearing[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2018, 48(2): 81 -85 .
[2] LI Ke,LIU Chang-chun,LI Tong-lei . Medical registration approach using improved maximization of mutual information[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2006, 36(2): 107 -110 .
[3] . [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2009, 39(1): 27 -32 .
[4] QIN Tong, SUN Fengrong*, WANG Limei, WANG Qinghao, LI Xincai. 3D surface reconstruction using the shape based interpolation guided by maximal discs[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2010, 40(3): 1 -5 .
[5] LIU Wen-liang, ZHU Wei-hong, CHEN Di, ZHANG Hong-quan. Detection and tracking of moving targets using the morphology match in radar images[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2010, 40(3): 31 -36 .
[6] WANG Li-ju,HUANG Qi-cheng,WANG Zhao-xu . [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2006, 36(6): 51 -56 .
[7] SUN Dianzhu, ZHU Changzhi, LI Yanrui. [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2009, 39(1): 84 -86 .
[8] YUE Yuan-Zheng. Relaxation in glasses far from equilibrium[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2009, 39(5): 1 -20 .
[9] CHENG Daizhan, LI Zhiqiang. A survey on linearization of nonlinear systems[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2009, 39(2): 26 -36 .
[10] LI Hui-ping, ZHAO Guo-qun, ZHANG Lei, HE Lian-fang. The development status of hot stamping and quenching of ultra high-strength steel[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2010, 40(3): 69 -74 .