虾米腰弯管内置导流板优化

doi:10.6040/j.issn.1672-3961.0.2020.093

摘要/Abstract

摘要：

为研究虾米腰弯管内流场分布，改善管内流场均匀性，采用Realizable k-ε模型对加装导流板前后的弯管内湍流二次流动进行三维数值模拟研究。结果表明：虾米腰弯管内未布置导流板时，在流体转弯后水平直管段出现较大范围的低速区，同时出现回流现象，气流分布极不均匀且阻力损失较大。布置导流板后，能有效改善弯管内流体的流动特性并降低系统能量损失。分析不同数量、不同结构、不同布置方式的导流板对弯管内流场均匀性、进出口压降的影响，提出虾米腰弯管内导流板最优布置方式为：导流板的数量为3块、中心角为60°、导流板均靠后布置。

关键词: 弯管, 流场优化, 阻力损失, 导流板, 数值模拟

Abstract:

In order to study the distribution of the flow field and improve the uniformity of the flow field in a shrimp-waist bend, a series of three-dimensional numerical simulation studies on the turbulent secondary flow in a bend before and after the installation of the deflector was carried out by using the Realizable k-ε model. The results showed that when the deflector was not arranged in the shrimp-waist bend pipe, a large range of low-speed zones appeared in the horizontal straight pipe section after the fluid turns, and a backflow phenomenon occured at the same time. The airflow distribution was extremely uneven and the pressure resistance was large. After the deflector was arranged, the flow characteristics of the fluid in the elbow were effectively improved and the energy loss of the system was reduced. Based on the analysis of the influence of different number, structure and arrangement of deflectors on the uniformity of flow field and pressure drop loss of the bend, the optimal arrangement of deflectors in the shrimp-waist bend was proposed as follows: the number of deflectors was 3, the deflectors′ center angle was 60°, and the deflectors were all arranged backward.

Key words: elbow, flow field optimization, resistance loss, deflector, numerical simulation

中图分类号:

TB126

祁金胜, 曹洪振, 石岩, 杜文静, 王湛. 虾米腰弯管内置导流板优化[J]. 山东大学学报 (工学版), 2020, 50(5): 64-69.

Jinsheng QI, Hongzhen CAO, Yan SHI, Wenjing DU, Zhan WANG. Optimization of the inner deflector of the shrimp-waist elbow[J]. Journal of Shandong University(Engineering Science), 2020, 50(5): 64-69.

图/表 13

图1

图2

图3

图4

图5

图6

图7

图8

图9

图10

图11

图12

图13

参考文献 20

1	STUDENT O Z , SVIRS′KA L M , Dzioba I R . Influence of the long-term operation of 12Kh1M1F steel from different zones of a bend of steam pipeline of a thermal power plant on its mechanical characteristics[J]. Materials Science, 2012, 48 (2): 239- 246. doi: 10.1007/s11003-012-9498-6
2	KUAN B , YANG W , SCHWARZ M P . Dilute gas-solid two-phase flows in a curved duct bend: CFD simulation with experimental validation[J]. Chemical Engineering Science, 2007, 62 (7): 2068- 2088. doi: 10.1016/j.ces.2006.12.054
3	陈冠益, 耿页, 原国栋, 等. 新型电厂烟道弯头的设计及数值模拟[J]. 天津大学学报(自然科学与工程技术版), 2015, 48 (6): 93- 99.
	CHEN Guanyi , GENG Ye , YUAN Guodong , et al. Numerical simulation and design of new power plant-based flue duct bend[J]. Journal of Tianjin University(Science and Technology), 2015, 48 (6): 93- 99.
4	赵全斌, 薛朝囡, 刘明, 等. 火电厂烟风通道主要异形件优化研究[J]. 工程热物理学报, 2015, 36 (4): 780- 784.
	ZHAO Quanbin , XUE Chaonan , LIU Ming , et al. Optimization on main types of major irregular parts for air & flue gas ducts in thermal power plant[J]. Journal of Engineering Thermophysics, 2015, 36 (4): 780- 784.
5	ZHANG Y , MCLAURY B S , SHIRAZI S A . Improvements of particle near-wall velocity and erosion predictions using a commercial CFD code[J]. Journal of Fluids Engineering, 2009, 131 (3): 031303. doi: 10.1115/1.3077139
6	El-BEHERY S M , HAMED M H , IBRAHIM K A , et al. CFD evaluation of solid particles erosion in curved ducts[J]. Journal of Fluids Engineering, 2010, 132 (7): 071303. doi: 10.1115/1.4001968
7	LIN Nan , LAN Huiqing , XU Yugong , et al. Effect of the gas-solid two-phase flow velocity on elbow erosion[J]. Journal of Natural Gas Science and Engineering, 2015, 26, 581- 586. doi: 10.1016/j.jngse.2015.06.054
8	刘荣堂, 王宇, 刘明, 等. 燃煤电站除尘器前烟道磨损特性与优化研究[J]. 工程热物理学报, 2019, 40 (4): 88- 92.
	LIU Rongtang , WANG Yu , LIU Ming , et al. Investigation and optimization on erosion characteristics of the flue gas pipe before the dust collector in power plants[J]. Journal of Engineering Thermophysics, 2019, 40 (4): 88- 92.
9	于飞, 刘明, 王汀, 等. 弯头内气-固两相流动与管壁磨损特性研究[J]. 工程热物理学报, 2015, 36 (4): 796- 800.
	YU Fei , LIU Ming , WANG Ting , et al. Numerical research on gas-solid two phase flow and erosion in elbows[J]. Journal of Engineering Thermophysics, 2015, 36 (4): 796- 800.
10	邹欢.锅炉尾部烟道烟气三维流场的数值模拟及均流装置的研究[D].济南:山东大学, 2013.
	ZOU Huan. Numerical simulation of three-dimensional gas flow field in boiler tail flue and study on flow-equalizing equipment [D]. Jinan: Shandong University, 2013.
11	TAYLOR A M K P . Curved ducts with strong secondary motion: velocity measurements of developing laminar and turbulent flow[J]. Journal of Fluids Engineering-transactions of the Asme, 1982, 104 (3): 350- 359. doi: 10.1115/1.3241850
12	KLIAFAS Y , Holt M . LDV measurements of a turbulent air-solid two-phase flow in a 90° bend[J]. Experiments in Fluids, 1987, 5 (2): 73- 85. doi: 10.1007/BF00776177
13	ENAYET M M , GIBSON M M , TAYLOR A M K P , et al. Laser-doppler measurements of laminar and turbulent flow in a pipe bend[J]. International Journal of Heat and Fluid Flow, 1982, 3 (4): 213- 219. doi: 10.1016/0142-727X(82)90024-8
14	谢振华, 周艳荣. 90°方截面弯管内加装导流板的优化研究[J]. 应用基础与工程科学学报, 2009, 17 (4): 79- 85.
	XIE Zhenhua , ZHOU Yanrong . Optimization research on guide plate installed in quadrate 90° curved duct[J]. Journal of Basic Science and Engineering, 2009, 17 (4): 79- 85.
15	周艳荣, 谢振华. 90°方截面弯管内气固两相流场的数值模拟[J]. 西安科技大学学报, 2008, 28 (1): 50- 54.
	ZHOU Yanrong , XIE Zhenhua . Numerical simulation of gas-solid two-phase flow in a 90° curved duct[J]. Journal of Xi′an University of Science and Technology, 2008, 28 (1): 50- 54.
16	于飞, 刘明, 李卫东, 等. 90°矩形截面弯头内置导流板的布置优化研究[J]. 动力工程学报, 2015, 35 (2): 147- 152.
	YU Fei , LIU Ming , LI Weidong , et al. Layout optimization of guide plates in a 90 degree elbow with rectangular cross section[J]. Journal of Chinese Society of Power Engineering, 2015, 35 (2): 147- 152.
17	贾兴豪, 彭向和, 龙血松. 导流板改善弯管流场的数值模拟与优化[J]. 西南大学学报(自然科学版), 2011, 33 (3): 139- 143.
	JIA Xinghao , PENG Xianghe , LONG Xuesong . Numerical simulation and optimization of flow field in elbow pipes with baffle[J]. Journal of Southwest University(Natural Science), 2011, 33 (3): 139- 143.
18	王周君, 黎星华, 唐立军, 等. 矩形截面直角弯管内置导流板的优化研究[J]. 华电技术, 2019, 41 (8): 32- 37.
	WANG Zhoujun , LI Xinghua , TANG Lijun , et al. Optimization research on deflectors installed in right-angle bend tube with rectangular sectior[J]. Huadian Techno-logy, 2019, 41 (8): 32- 37.
19	王宇, 何琪, 于飞, 等. 组合弯头内气固两相流动磨损特性的数值模拟与结构优化[J]. 中国电机工程学报, 2018, 38 (3): 832- 839.
	WANG Yu , HE Qi , YU Fei , et al. Numerical simulation of the erosion characteristics and structure optimization of elbows connection for gas-solid flow[J]. Proceedings of the CSEE, 2018, 38 (3): 832- 839.
20	SUN hongchuang , QIN Jiang , HUANG Hongyan , et al. Numerical simulation of flow and heat transfer in a square rotating U-duct using hydrocarbon fuel[J]. Journal of Heat Transfer, 2019, 141 (3): 031701. doi: 10.1115/1.4042299

多维度评价

Viewed

Full text

Abstract

Cited

Shared

Discussed

[1]	王心泉,王智猛,牛犇,蒋恒,冯春. 8度地震烈度区新民隧道出口处边坡的稳定性[J]. 山东大学学报 (工学版), 2023, 53(3): 23-30.
[2]	孙杰,张宏博,程钰,刘羽,张洪波,刘志鲲. 基于TDA填料的废旧轮胎条带加筋砂土边坡承载特性[J]. 山东大学学报 (工学版), 2023, 53(1): 49-59.
[3]	牛犇,张新伟,周玉,李婧,徐兴全,张一鸣. 基于连续-非连续元降雨工况三维边坡稳定性分析[J]. 山东大学学报 (工学版), 2023, 53(1): 92-99.
[4]	郭鹏宁,刘巍,袁浩,冯硕,王延刚. 基于微元离散模型的螺旋挤压脱水效率分析[J]. 山东大学学报 (工学版), 2023, 53(1): 114-121.
[5]	张一鸣,李赟鹏,李婧,丛俊余. 孔隙裂隙介质多场耦合数值计算进展[J]. 山东大学学报 (工学版), 2022, 52(6): 63-78.
[6]	郑卫琴,许杰,孙杰,武科. 复合地层TBM隧道管片受力特征[J]. 山东大学学报 (工学版), 2022, 52(4): 210-213.
[7]	章清涛,刘晓威,高健,孙玉海,闫庆亮,刘源,王昊. 坡顶荷载作用下废旧轮胎条带加筋边坡承载特性[J]. 山东大学学报 (工学版), 2022, 52(3): 70-79.
[8]	刘舫辰,石岩,李元鲁,王湛,杜文静,季万祥. 用于燃煤电厂的低温省煤器前烟道流动及磨损特性[J]. 山东大学学报 (工学版), 2022, 52(3): 100-108.
[9]	郑俊峰,陈晓燕,马正,陈青. 土石坝加固拓宽坝体变形及稳定性分析[J]. 山东大学学报 (工学版), 2022, 52(1): 85-92.
[10]	田利,毕文哲,SIDDIQUISarim Saleem,刘凯悦. 建筑结构抗下击暴流研究综述[J]. 山东大学学报 (工学版), 2021, 51(5): 32-41.
[11]	卢光兆,周博,徐锋,上官伟,王刚,张书博. 浅埋偏压隧道进洞施工围岩稳定分析[J]. 山东大学学报 (工学版), 2021, 51(4): 61-70.
[12]	王春国. 硬岩隧道施工通风系统优化与抑尘效果评价[J]. 山东大学学报 (工学版), 2021, 51(3): 52-60.
[13]	王春国. 复合地层全断面硬岩隧道掘进机下穿立交桥研究[J]. 山东大学学报 (工学版), 2021, 51(3): 45-51.
[14]	孙杰,武科,郑扬,李树忱,袁超,王修伟. 城市地铁TBM隧道掘进诱发既有建筑物变形的空间属性效应[J]. 山东大学学报 (工学版), 2021, 51(1): 32-38.
[15]	苏思博,王国清,贾献卓,李志聪,黄志刚. 剪跨比对插槽式连接空心管墩抗震性能影响[J]. 山东大学学报 (工学版), 2021, 51(1): 39-45.