变加热功率下不同形状微肋阵热沉内的对流换热

doi:10.6040/j.issn.1672-3961.0.2015.210

山东大学学报(工学版) ›› 2016, Vol. 46 ›› Issue (2): 128-134.doi: 10.6040/j.issn.1672-3961.0.2015.210

• • 上一篇

变加热功率下不同形状微肋阵热沉内的对流换热

管宁¹,栾涛^1*,刘志刚²,张承武²,姜桂林²,邱德来²

1. 山东大学能源与动力工程学院, 山东济南 250061;2. 山东省科学院能源研究所, 山东济南 250014

收稿日期:2015-07-03 出版日期:2016-04-20 发布日期:2015-07-03
通讯作者: 栾涛(1962— ),男,山东淄博人,教授,博士,主要研究方向为强化传热与节能技术. E-mail:tluan@sdu.edu.cn E-mail:nn01006101@163.com
作者简介:管宁(1983— ),女,山东潍坊人,副研究员,博士研究生,主要研究方向为微尺度流动及强化换热.E-mail: nn01006101@163.com
基金资助:
国家自然科学基金资助项目(51306107);山东省科技发展计划资助项目(2014GGX104008)

Convective heat transfer in micro pin fin heat sinks with different cross section shapes under variable heating loads

GUAN Ning¹, LUAN Tao^1*, LIU Zhigang², ZHANG Chengwu², JIANG Guilin², QIU Delai²

1. School of Energy and Power Engineering, Shandong University, Jinan 250061, Shandong, China;
2. Energy Research Institute, Shandong Academy of Sciences, Jinan 250014, Shandong, China

Received:2015-07-03 Online:2016-04-20 Published:2015-07-03

摘要/Abstract

摘要： 为探索变加热功率下微肋阵热沉内的对流换热规律,采用精密机械加工获得圆形、菱形和三角形微肋阵热沉,建立一体式加热试验系统,测试了微肋阵热沉的压力降、流动阻力系数、热阻等对流换热参数,研究Re为0~1 000时微肋阵内阻力及对流换热受加热功率的影响规律。研究结果表明,微肋阵内阻力系数先随加热功率增加而增大,圆形和菱形截面微肋阵中该现象在Re>400时消失,而三角形微肋阵在Re>250时消失。加热功率的增加强化了圆形和菱形截面微肋阵内的对流换热,三角形微肋阵的Nu在Re<250时随加热功率的增加而增大,当Re>250后则有所降低;加热功率对于圆形和菱形微肋阵热沉热阻的影响在Re<600时较为明显,而对于三角形微肋阵当Re>250后加热功率对于热阻的影响基本可以忽略。

关键词: 微肋阵, 阻力, 微通道, 传热, 对流换热, 加热功率, 流动

Abstract: In order to investigate the flow and convective heat transfer characteristics under different heating loads in micro pin fins,test sections of micro pin fins with different cross section shapes of circle, diamond and triangle were precision machined. An integraed heating system was used to to measure the pressure drops, frictional resistance factors and thermal resistance in micro pin fins. Based on the experimental results, the impact of heating load on the flow resistance and the heat transfer in micro pin fins with Reynolds number ranging from 0~1 000 was explored. It was found that the friction factors in the three types of micro pin fins became large with the increase of the heating load, but this phenomenon disappeared when Re>400 for the circle and diamond micro pin fins, and Re>250 for the triangular micro pin fins. The convective heat transfer in micro pin fins with cross section shapes of circle, diamond was enhanced by increasing the heating load, but the Nu in triangular micro pin fins became large with the increase of the heating load when Re<250, and then it became slightly smaller when Re>250.

Key words: microchannels, heat transfer, convective heat transfer, micro pin fins, heating loads, flow resistance, flow

中图分类号:

TK124

管宁,栾涛,刘志刚,张承武,姜桂林,邱德来. 变加热功率下不同形状微肋阵热沉内的对流换热[J]. 山东大学学报(工学版), 2016, 46(2): 128-134.

GUAN Ning, LUAN Tao, LIU Zhigang, ZHANG Chengwu, JIANG Guilin, QIU Delai. Convective heat transfer in micro pin fin heat sinks with different cross section shapes under variable heating loads[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2016, 46(2): 128-134.

参考文献

[1] MOHAMMAD M M, KOK-CHEONG W, MANSOOR S. Numerical investigation of fluid flow and heat transfer under high heat flux using rectangular micro-channels[J]. International Journal of Commumications in Heat and Mass Transfer, 2012, 39(2): 291-297.
[2] HAMID R S, MORTEZA F. Computational analysis of nanofluid effects on convective heat transfer enhancement of micro-pin-fin heat sinks[J]. International Journal of Thermal Science, 2012, 58:168-179.
[3] PELES Y, KO??塁AR A, MISHRA C, et al. Forced convective heat transfer across a pin fin micro heat sink[J]. International Journal of Heat and Mass Transfer, 2005, 48(17):3615-3627.
[4] KO??塁AR A, MISHRA C, PELES Y. Laminar flow across a bank of low aspect ratio micro pin fins[J]. Journal of Fluids Engineering, 2005, 127(3):419-430.
[5] KO??塁AR A, PELES Y. Thermal-hydraulic performance of MEMES-based pin fin heat sink[J]. Journal of Heat Transfer, 2006, 128(2):121-131.
[6] MUSTAFA K, MEHMED R O, KO??塁AR A. Parametric study on the effect of end walls on heat transfer and fluidflow across a micro pin-fin[J]. International Journal of Thermal Science, 2011, 50(6):1073-1084.
[7] CHANG S W Y W HU. Endwall thermal of performances of radially rotating rectangular channel with pin-fins on skewed rib lands [J]. International Journal of Heat and Mass Transfer, 2014, 69:173-190.
[8] 张承武,刘志刚,管宁.加热热通量对微柱群通道内强迫对流换热的影响[J].化工学报,2010,61(12):3080-3085. ZHANG Chengwu, LIU Zhiang, GUAN Ning. Influence of heat flux on forced convective heat transfer in duct with micro-cylinder-group [J]. CIESC Journal, 2010, 61(12):3080-3085.
[9] 张承武,浦龙梅,姜桂林等.不同截面形状微肋片内流动阻力特性[J].化工学报,2014,65(6):2042-2048. ZHANG Chengwu, PU Longmei, JIANG Guilin, et al. Resistance characteristics of micro pin fins with different cross-section shapes[J]. CIESC Journal, 2014, 65(6):2042-2048.
[10] TULLIUS J F, TULLIUS T K, Bayazitoglu Y. Optimization of short micro pin fins in minichannels[J]. International Journal of Heat and Mass Transfer, 2012, 55(15-16):3921-3932.
[11] ADEWUMI O O, BELLO-OCHENDE T, MEYER J P. Constructal design of combined microchannel and micro pin fins for electronic cooling[J]. International Journal of Heat and Mass Transfer, 2013, 66:315-323.
[12] MOORES K A, KIM J, JOSHI Y. Effect of tip clearance on the thermal and hydrodynamic performance of shrouded pin fin arrays[D]. Maryland: Department of Mechanical Engineering, University of Maryland, 2008.
[13] MOORES K A, KIM J, JOSHI Y K. Heat transfer and fluid flow in shrouded pin fin arrays with and without tip clearance[J]. International Journal of Heat and Mass Transfer, 2009, 52(25-26):5978-5989.
[14] REINHARD R, GABRIEL L, KEITH C, et al. Heat transfer in freestanding microchannels with in-line and staggered pin fin structures with clearance[J]. International Journal of Heat and Mass Transfer, 2013, 67:1-15.
[15] MEI D Q, LOU XY, QIAN M, et al. Effect of tip clearance on the heat transfer and pressure drop performance in the micro-reactor with micro-pin-fin arrays at low Reynolds number[J]. International Journal of Heat and Mass Transfer, 2014, 70:709-718.
[16] REYES M, ARIAS J R, VELAZQUEZ A, et al. Experimental study of heat transfer and pressure drop in micro-channel based heat sinks with tip clearance[J]. Applied Thermal Engineering, 2011, 31(5):887-893.
[17] 刘志刚,张承武,管宁.叉排微柱群内顶部间隙对传热效率的影响[J].化工学报,2012,63(4):1025-1031. LIU Zhigang, ZHANG Chengwu, GUAN Ning. Influence of tip clearance on heat transfer efficiency in staggered micro-cylinders-group[J]. CIESC Journal, 2012, 63(4):1025-1031.
[18] SHAHABEDDIN K M, YUWEN Z. Analysis of nanofluid effects on thermoelectric cooling by micro-pin-fin heat exchangers[J]. Applied Thermal Engineering, 2014, 70(1):282-290.
[19] MUSHTAQ I H. Investigation of flow and heat transfer characteristics in micro pin fin heat sink with nano fluid[J]. Applied Thermal Engineering, 2014, 63(2):598-607.
[20] ABAS A, JIMENEZ G, DULIKRAVICH G S. Thermo-fluid analysis of micro pin fin array cooling cofigurations for high heat fluxes with a hot spot[J]. International Journal of Thermal Science, 2015, 90:290-297.
[21] MOFFAT R J. Describing the uncertainties in experimental results [J]. Experimental Thermal and Fluid Science, 1988, 1(1):3-17.

多维度评价

Viewed

Full text

Abstract

Cited

Shared

Discussed

变加热功率下不同形状微肋阵热沉内的对流换热

Convective heat transfer in micro pin fin heat sinks with different cross section shapes under variable heating loads

PDF (PC)

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

多维度评价

本文评价

推荐阅读 10

[1]	刘健,胡南琦,徐宝军,岳秀丽,齐泊良,仲奇. 水泥基土石坝防渗注浆材料试验[J]. 山东大学学报(工学版), 2018, 48(2): 39-45.
[2]	王丹华,张冠敏,冷学礼,徐梦娜,韩圆圆. T型管内两相流分配特性数值模拟[J]. 山东大学学报(工学版), 2018, 48(1): 89-95.
[3]	李连祥,李先军. 不同扩径体数量、位置对支盘桩承载力的影响[J]. 山东大学学报(工学版), 2016, 46(5): 88-94.
[4]	吴艳艳, 孙奉仲, 李飞, 陈昌贤. H型翅片管束空气流动及换热特性[J]. 山东大学学报(工学版), 2014, 44(6): 90-94.
[5]	冀翠莲, 韩吉田, 尹静, 陈常念, 任立波, 孔令健. 螺旋管内流动沸腾传热系数关联式拟合与误差分析[J]. 山东大学学报(工学版), 2014, 44(5): 83-87.
[6]	张涛, 韩吉田, 闫素英, 于泽庭, 周然. 太阳能真空管的热性能分析与测试[J]. 山东大学学报(工学版), 2014, 44(4): 76-83.
[7]	陈昌贤, 孙奉仲, 李飞, 吴艳艳. 四分仓回转式空气预热器热力计算方法[J]. 山东大学学报(工学版), 2014, 44(4): 58-63.
[8]	李飞, 孙奉仲, 史月涛, 马磊. 圆管管束特性试验及协同分析[J]. 山东大学学报(工学版), 2014, 44(4): 70-75.
[9]	程屾, 孙奉仲*. 渗层不锈钢管束表面真空下换热特性的实验分析[J]. 山东大学学报(工学版), 2014, 44(1): 90-94.
[10]	车翠翠,田茂诚*,冷学礼. 翼片诱导纵向涡强化层流对流传热数值模拟[J]. 山东大学学报(工学版), 2013, 43(5): 104-110.
[11]	谭鲁志,韩吉田*,陈常念,孔令健,冀翠莲,逯国强. 卧式螺旋管临界热流密度的流体模化[J]. 山东大学学报(工学版), 2013, 43(3): 87-93.
[12]	吕明新1,2,宋固1,董震1,魏露露1, 赖艳华1*. 两级反射线性菲涅尔中高温集热系统热性能[J]. 山东大学学报(工学版), 2013, 43(2): 105-110.
[13]	张井志,田茂诚*,张冠敏,冷学礼. 板式换热器触点分布对换热阻力性能的影响[J]. 山东大学学报(工学版), 2012, 42(6): 121-126.
[14]	姜波1,田茂诚2*,郝卫东1, 刘福国1. 新型弹性管束固有振动特性实验及数值模拟[J]. 山东大学学报(工学版), 2012, 42(4): 132-136.
[15]	王虹入1,王中秋1, 3*, 张倩2,李剑峰3, 孙杰3. 切削法构建铝合金Al7050-T7451材料流动应力本构模型[J]. 山东大学学报(工学版), 2012, 42(1): 115-120.