基于微元离散模型的螺旋挤压脱水效率分析

doi:10.6040/j.issn.1672-3961.0.2021.372

摘要/Abstract

摘要：

为研究螺旋挤压机构中各参数对餐厨垃圾脱水效率的影响, 构建一种联系物料特性与螺旋挤压装置参数的微元离散模型, 结合数值模拟方式, 对物料初始含水率、物料填充程度、螺旋叶片形式以及螺旋转速4个影响装置脱水效率的因素进行理论计算。在构建模型过程中, 利用正交试验分析方法, 筛选出脱水效率相对最优的参数方案, 为螺旋挤压机构的设计选型提供了理论依据。计算结果表明: 螺旋转速和物料填充程度对装置脱水效率的影响显著, 最高脱水率高达40%和40.6%;物料初始含水率和螺旋叶片形式对装置脱水效率影响较小, 最高脱水率仅为16.6%和14.8%。正交试验结果表明: 物料初始含水率为80%, 物料填充系数为75%, 螺旋转速为15 r/min的变螺距螺旋叶片结构, 物料末端含水率为69.7%, 综合考虑能源消耗、工作效率以及性价比等因素, 该参数在实际工况中最有优势。

关键词: 餐厨垃圾, 螺旋挤压, 离散模型, 固液分离, 数值模拟

Abstract:

In order to study the effect of screw extrusion mechanism on the dewatering efficiency of food waste, a micro element discrete model connecting material characteristics and screw extrusion device parameters was constructed, combined with numerical simulation, the four factors affecting the dehydration efficiency of the unit, such as the initial moisture content of materials, the filling degree of materials, the form of spiral blades and the spiral speed, were theoretically calculated. In the process of building the model, the parameter scheme with relatively optimal dehydration efficiency was selected by using the analysis method of orthogonal test. The conclusion provided a theoretical basis for the design and selection of screw extrusion mechanism. The calculation results showed that the screw speed and material filling degree had a significant impact on the dehydration efficiency of the unit, and the maximum dehydration rates were up to 40% and 40.6%. The initial moisture content of materials and the form of spiral blades had little influence on the dehydration efficiency of the unit, and the maximum dehydration rates were only 16.6% and 14.8%. The orthogonal test results showed that the moisture content at the end of the material was 69.7% for variable pitch helical blade structure, under the condition that the initial moisture content of the material was 80%, the material filling coefficient was 75%, and the screw speed was 15 r/min. Considering the factors such as energy consumption, work efficiency and cost performance, the parameter condition had the most advantages in the actual working conditions.

Key words: food waste, screw extrusion, discrete model, solid-liquid separation, numerical simulation

中图分类号:

TH122

郭鹏宁,刘巍,袁浩,冯硕,王延刚. 基于微元离散模型的螺旋挤压脱水效率分析[J]. 山东大学学报 (工学版), 2023, 53(1): 114-121.

Pengning GUO,Wei LIU,Hao YUAN,Shuo FENG,Yangang WANG. Analysis of screw extrusion dehydration efficiency based on micro element discrete model[J]. Journal of Shandong University(Engineering Science), 2023, 53(1): 114-121.

图/表 17

图1

图2

图3

图4

图5

图6

表1

图7

图8

图9

图10

表2

表3

图11

图12

图13

图14

参考文献 24

1	王凯军, 王婧瑶, 左剑恶, 等. 我国餐厨垃圾厌氧处理技术现状分析及建议[J]. 环境工程学报, 2020, 14 (7): 1735- 1742.
	WANG Kaijun , WANG Jingyao , ZUO Jian'e , et al. Analysis and suggestion of current food waste anaerobic digestion technology in China[J]. Chinese Journal of Environmental Engineering, 2020, 14 (7): 1735- 1742.
2	饶玲华, 李军. 餐厨垃圾资源化处理方案对比分析[J]. 环境科学与技术, 2016, 39 (2): 237- 240.
	RAO Linghua , LI Jun . Analysis and comparison of food waste resource treatment technologies[J]. Chinese Journal of Environmental Engineering, 2016, 39 (2): 237- 240.
3	SRIVASTAVA N , SRIVASTAVA M , ABD_ALLAH E F , et al. Biohydrogen production using kitchen waste as the potential substrate: a sustainable approach[J]. Chemosphere, 2021, 271, 129537. doi: 10.1016/j.chemosphere.2021.129537
4	CAPSON-TOJO G , TRABLY E , ROUEZ M , et al. Dry anaerobic digestion of food waste and cardboard at different substrate loads, solid contents and co-digestion proportions[J]. Bioresource Technology, 2017, 233, 166- 175. doi: 10.1016/j.biortech.2017.02.126
5	XU F , LI Y , GE X , et al. Anaerobic digestion of food waste: challenges and opportunities[J]. Bioresource Technology, 2018, 247, 1047- 1058. doi: 10.1016/j.biortech.2017.09.020
6	班福忱, 孙晓昕, 刘鑫, 等. 自动分选+固液分离+油水分离工艺餐厨垃圾处理工程[J]. 环境工程, 2016, 34 (8): 145- 148.
	BAN Fuchen , SUN Xiaoxin , LIU Xin , et al. Introduction to a food waste treatment project with automatic sorting, solid-liquid separation, and oil-water separation process[J]. Environmental Engineering, 2016, 34 (8): 145- 148.
7	ROSTI M E , PRAMANIK S , BRANDT L , et al. The breakdown of Darcy's law in a soft porous material[J]. Soft Matter, 2020, 16 (4): 939- 944. doi: 10.1039/C9SM01678C
8	李鑫. 基于挤出理论的螺旋挤压脱水机机理研究[D]. 北京: 北京化工大学, 2011.
	LI Xin. Mechanisim study of screw sqeezer based on extrud theory[D]. Beijing: Beijing University of Chemical Technology, 2011.
9	WAKEMAN R J . Separation technologies for sludge dewatering[J]. Journal of Hazardous Materials, 2007, 144 (3): 614- 619. doi: 10.1016/j.jhazmat.2007.01.084
10	KUHN M , PERGAM P , BRIESEN H . Parameter estimation for incompressible cake filtration: advantages of a modified fitting method[J]. Chemical Engineering & Technology, 2020, 43 (3): 493- 501.
11	杨阳. 高黏度物料固液挤压分离技术与装备研究[D]. 北京: 北京化工大学, 2018.
	YANG Yang. Research on solid-liquid extrusion separation technology and equipment for high viscosity materials[D]. Beijing: Beijing University of Chemical Technology, 2018.
12	赵扬. 滤饼微观结构与压榨过滤理论的研究[D]. 杭州: 浙江大学, 2006.
	ZHAO Yang. Study on the microstructure of the filter cake and the expression filtration theory[D]. Hangzhou: Zhejiang University, 2006.
13	孙明文. 一维恒压压榨脱水理论在过滤机中应用[J]. 机械设计与制造, 2006, 3 (3): 49- 51.
	SUN Mingwen . The application of one-dimensional constant pressure expression and dewatering theory in filter[J]. Machinery Design and Manufacture, 2006, 3 (3): 49- 51.
14	邱爱红, 龚曙光, 谢桂兰, 等. 变径变螺距螺旋轴参数化模型及性能仿真[J]. 机械工程学报, 2008, 44 (5): 131- 136.
	QIU Aihong , GONG Shuguang , XIE Guilan , et al. Parametric model and performance simulation on the screw conveyor of variable diameters and variable pitches[J]. Chinese Journal of Mechanical Engineering, 2008, 44 (5): 131- 136.
15	武军, 范德顺. 间断式螺旋挤压过滤机[J]. 过滤与分离, 2008, 18 (1): 36- 37.
	WU Jun , FAN Deshun . Interrupted screw filter[J]. Journal of Filtration & Separation, 2008, 18 (1): 36- 37.
16	HILLIG É , IWAKIRI S , HASELEIN C R , et al. Characterization of composites made of HDPE and furniture industry sawdust: Part Ⅱ: double-screw extrusion[J]. Ci ncia Florestal, 2011, 21 (2): 335- 347.
17	李佟, 李军, 刘伟岩, 等. 螺旋压榨式脱水机对污泥脱水的试验研究[J]. 中国给水排水, 2009, 25 (11): 66- 68.
	LI Tong , LI Jun , LIU Weiyan , et al. Experimental research on sludge dewatering by screw press dehydrator[J]. China Water & Wastewater, 2009, 25 (11): 66- 68.
18	PRADHAN R C , MISHRA S , NAIK S N , et al. Oil expression from Jatropha seeds using a screw press expeller[J]. Biosystems Engineering, 2011, 109 (2): 158- 166.
19	赵维松. 螺旋挤压固液分离机构优化设计与试验[D]. 南京: 中国农业科学院, 2017.
	ZHAO Weisong. Organization design and experiments of screw separator[D]. Nanjing: Chinese Academy of Agricultural Sciences, 2017.
20	ZHANG H R , ZHANG B . Research on screw-extrusion dehydration technology and equipment in recycling process of urban garbage[J]. Applied Mechanics and Materials, 2015, 768, 273- 280.
21	张龙龙. 秸秆螺旋挤压脱水机的数值模拟研究[D]. 郑州: 郑州大学, 2015.
	ZHANG Longlong. Numerical simulation on screw extruder of straw[D]. Zhengzhou: Zhengzhou Univer-sity, 2015.
22	王延刚, 常皓, 王金帅, 等. 一种餐厨垃圾处理装置: 202010659259.2[P]. 2020-09-25.
23	孙邦雨. 城市餐厨垃圾固液分离技术与装备研究[D]. 北京: 北京化工大学, 2017.
	SUN Bangyu. Research on municipal food waste solid-liquid separation and facility development[D]. Beijing: Beijing University of Chemical Technology, 2017.
24	CERVON N W , HARPER J M . Viscosity of an intermediate moisture dough[J]. Journal of Food Process Engineering, 1978, 2 (1): 83- 95.

多维度评价

Viewed

Full text

Abstract

Cited

Shared

Discussed

常规螺距p/mm	螺旋叶片直径d/mm	叶片外径D/mm
80	40	80

流道长度l/mm	螺旋厚度e/mm	螺旋升角φ/(°)
480	3.5	27.26

变径锥角θ/(°)		变螺距p/mm

2.29		55、65、75、85、95、105

因素水平	初始含水率/%	填充系数/%	螺旋形式	螺旋转速/(r·min^-1)
1	95	80	类型1	15
2	90	75	类型2	20
3	85	70	类型3	25
4	80	65	类型4	30

[1]	刘启明,王文辉,潘英楠,高要辉,郑程程,贺鹏. 厚度缺陷对初支结构安全性的影响及风险评价[J]. 山东大学学报 (工学版), 2025, 55(5): 165-178.
[2]	义扬,肖映雄,余科. 任意多边形骨料混凝土细观模型的建立与数值模拟[J]. 山东大学学报 (工学版), 2025, 55(1): 97-107.
[3]	陈文举, 陈俐企, 包春波, 朱启银, 惠冰, 庄培芝. 循环管道加热桥面融雪效能数值模拟[J]. 山东大学学报 (工学版), 2024, 54(6): 100-110.
[4]	马川义,冯豪杰,蒋红光,侯天新,姚占勇,杨为民. 吸水土工布对路基湿度控制效果的数值模拟[J]. 山东大学学报 (工学版), 2024, 54(4): 141-149.
[5]	韩超,王彤,陈德文,孙恩赐,李平,吴则祥,周冲,庄培芝. 基于耦合欧拉-拉格朗日方法的砂土中静压桩挤土效应数值模拟[J]. 山东大学学报 (工学版), 2024, 54(2): 143-152.
[6]	王钰鑫,吕思忠,姚望,林春金,张明,李召峰,张健,王衍升. 粉质黏土地层桩侧劈裂注浆参数设计与效果评价[J]. 山东大学学报 (工学版), 2023, 53(6): 70-81.
[7]	张亚平,马唯婧,张宸硕,肖辉,张一鸣. 基于图像识别与CAE仿真技术的输变电塔一体化分析[J]. 山东大学学报 (工学版), 2023, 53(6): 122-130.
[8]	宋洋,罗志恒,张波,张宇,朱敏. 裂隙位置对类岩体短柱单轴压缩破坏形态影响[J]. 山东大学学报 (工学版), 2023, 53(5): 121-131.
[9]	王心泉,王智猛,牛犇,蒋恒,冯春. 8度地震烈度区新民隧道出口处边坡的稳定性[J]. 山东大学学报 (工学版), 2023, 53(3): 23-30.
[10]	孙杰,张宏博,程钰,刘羽,张洪波,刘志鲲. 基于TDA填料的废旧轮胎条带加筋砂土边坡承载特性[J]. 山东大学学报 (工学版), 2023, 53(1): 49-59.
[11]	牛犇,张新伟,周玉,李婧,徐兴全,张一鸣. 基于连续-非连续元降雨工况三维边坡稳定性分析[J]. 山东大学学报 (工学版), 2023, 53(1): 92-99.
[12]	张一鸣,李赟鹏,李婧,丛俊余. 孔隙裂隙介质多场耦合数值计算进展[J]. 山东大学学报 (工学版), 2022, 52(6): 63-78.
[13]	郑卫琴,许杰,孙杰,武科. 复合地层TBM隧道管片受力特征[J]. 山东大学学报 (工学版), 2022, 52(4): 210-213.
[14]	章清涛,刘晓威,高健,孙玉海,闫庆亮,刘源,王昊. 坡顶荷载作用下废旧轮胎条带加筋边坡承载特性[J]. 山东大学学报 (工学版), 2022, 52(3): 70-79.
[15]	刘舫辰,石岩,李元鲁,王湛,杜文静,季万祥. 用于燃煤电厂的低温省煤器前烟道流动及磨损特性[J]. 山东大学学报 (工学版), 2022, 52(3): 100-108.