ChinZA合金TIG焊剂对焊接电弧及焊缝成型的影响

山东大学学报(工学版)

ChinZA合金TIG焊剂对焊接电弧及焊缝成型的影响

刘秀忠，李士同，伦宁，杨敏

山东大学材料科学与工程学院, 山东济南250061

收稿日期:2007-04-06 修回日期:1900-01-01 出版日期:2007-12-24 发布日期:2007-12-24
通讯作者: 刘秀忠

Study on the effect of ZA alloy TIG flux on the weld formation and welding arc

LIU Xiu-zhong，LI Shi-tong, LUN Ning，YANG Min

School of Materials Science and Engineering,Shandong University,Jinan 250061,China

Received:2007-04-06 Revised:1900-01-01 Online:2007-12-24 Published:2007-12-24
Contact: LIU Xiu-zhong

摘要/Abstract

摘要： 研究了ZA合金TIG焊中不同的焊剂对焊接电弧及焊缝成型的影响.结果发现:加入 KCl焊剂电弧形状变化不大；加入LiCl焊剂电弧有收缩和“粘着”现象，电弧的宽度增加，长度减少,但阳极斑点不明显突出；加入KF焊剂电弧有明显突出的阳极斑点产生，阴极区有所收缩；加入ZnCl2焊剂电弧的宽度和长度都有所增加，阳极斑点变小而突出；加入多组元混合焊剂电弧宽度增大，阳极斑点变小，且明显凸出，电弧长度变化不明显.电弧进入焊剂区时，焊缝表面宽度都有所减小，其中KF的减少最为明显,焊缝表面呈现金属光泽，ZnCl2最为光亮，而无焊剂区焊缝表面呈现明显的氧化现象.

关键词: ZA合金, TIG焊剂, 焊接电弧, 焊缝成型

Abstract: In the welding process of ZA alloy, the effect of flux on the shape and voltage of welding arc were investigated by using highspeed camera and oscillograph. The influence of TIG flux on weld formation was analyzed. Results show that TIG flux affected the shape of welding arc and the formation of anode spot. However, the flux didn't obviously influence the cathode conductive district. TIG flux can result in the increase of welding arc section area and make anode spot outstanding. The voltage of welding arc does not increased greatly. The KCl and KF in flux can lead to the reduction of both welding arc minor contraction and section area. LiCl and ZnCl2 can make the section area of welding arc increase. ZnCl2 can prompt the formation of anode spot and make it obvious. ZA alloy TIG flux also can make the surface of weld finely and reduce the weld width.

Key words: ZA alloy, TIG flux, welding arc, weld formation

中图分类号:

TG146

刘秀忠,李士同,伦宁,杨敏 . ChinZA合金TIG焊剂对焊接电弧及焊缝成型的影响[J]. 山东大学学报(工学版), 2007, 37(6): 44-48 .

LIU Xiu-zhong,LI Shi-tong,LUN Ning,YANG Min . Study on the effect of ZA alloy TIG flux on the weld formation and welding arc[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2007, 37(6): 44-48 .

参考文献

多维度评价

Viewed

Full text

Abstract

Cited

Shared

Discussed

[1]	郑林彬,王建明,何讯超. 2024铝合金喷丸粗糙度试验与数值模拟[J]. 山东大学学报(工学版), 2017, 47(1): 84-89.
[2]	刘学文,石元昌,柏其亚 . 烧结Al₂O₃陶瓷在海水中的耐腐蚀性能研究[J]. 山东大学学报(工学版), 2008, 38(5): 113-116 .
[3]	邹新国 . 铝合金中单层Mg-GP,Si-GP区的高分辨电子显微镜图像的计算机模拟[J]. 山东大学学报(工学版), 2008, 38(4): 75-79 .
[4]	郑洪亮,孔凡利, , 田学雷 . Al-Cu合金成分变化对其凝固潜热影响的研究[J]. 山东大学学报(工学版), 2008, 38(2): 10-12 .