JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE) ›› 2014, Vol. 44 ›› Issue (5): 83-87.doi: 10.6040/j.issn.1672-3961.0.2014.020

Previous Articles     Next Articles

Fitting heat transfer coefficient correlation on flow boiling and error analysis for the helically coiled tube

JI Cuilian1,2, HAN Jitian1, YIN Jing2, CHEN Changnian1, REN Libo1, KONG Lingjian1   

  1. 1. School of Energy and Power Engineering, Shandong University, Jinan 250061, Shandong, China;
    2. Municipal and Environmental Engineering Department, Shandong Urban Construction Vocational College, Jinan 250103, Shandong, China
  • Received:2014-01-13 Revised:2014-09-18 Published:2014-01-13

PDF (PC)

2237

Abstract: In order to develop flow boiling heat transfer coefficient correlations for helically coiled tube, based on the mechanism of flow boiling heat transfer. The Dn factor was introduced to consider complex pipeline effects on flow boiling heat transfer. The index of the Dn factor was gained by using the regression method. And relation of the ratio of the experimental and predicted values with the mass flow rate and vapor quality was further analyzed. A new heat transfer coefficient correlation of flow boiling in helically coiled tube was developed. The applicability for the heat transfer coefficient correlation was validated by experimental data of flow boiling heat transfer in helically coiled tube with R134a. The MRE and the RMSE were used to measure the accuracy of regression results, with MRE and RMSE being 8.23% and 0.532, respectively. The MRE and the RMSE were small, the regression results conformed to the requirements. Therefore, the method is very applicable, and is worthy of popularization.

Key words: flow boiling, heat transfer, two-phase flow, helically coiled tube, heat transfer coefficient correlation

CLC Number: 

  • TK 121
[1] 白博峰,郭烈锦.卧式螺旋管内流动沸腾传热研究[J].核科学与工程,1997,17(4):302-308.BAI Bofeng, GUO Liejin.Study on convective boiling heat transfer in horizontal helically coiled tubes[J].Nuclear Science and Engineering, 1997, 17(4):302-308.
[2] 陈常念,韩吉田,邵莉,等.R134a卧式螺旋管内流动沸腾CHF特性研究[J].核动力工程,2010,31(5):76-80.CHEN Changnian, HAN Jitian, SHAO Li, et al.Study on dry-out CHF characteristics of R134a flow boiling in horizontal helically coiled tube[J].Nuclear Power Engineering, 2010, 31(5):76-80.
[3] 郭烈锦,陈学俊,张鸣远.卧式螺旋管内汽水两相流沸腾传热特性研究[J].西安交通大学学报,1994, 28(5):120-124.GUO Liejin, CHEN Xuejun, ZHANG Mingyuan.Research on the forced convective boiling heat transfer characteristics of steam water two-phase flow in horizontal helically coiled tubes[J].Journal of Xian Jiaotong University, 1994, 28(5):120-124.
[4] CHEN C N, HAN J T, JEN T C, et al.Fluid-to-fluid modeling of two-phase flow critical heat flux in horizontal helically coiled tubes[J].Nuclear Engineering and Design, 2011, 241(3):1430-1437.
[5] 邵莉.R134a在卧式螺旋管内的两相流动与传热特性研究[D].济南:山东大学,2009.SHAO Li.Study on two-phase flow and heat transfer characteristics of R134a in helical coils tubes[D].Jinan:Shandong University, 2009.
[6] OWHADI A, BELL K J, CRAIN J.Forced convection boiling inside helically coiled tubes[J].International Journal of Mass Transfer, 1968, 11(11):1179-1793.
[7] KOZEKI M, NARIAI H, FURUKAWA T, et al.A study of helically coiled tube once-through steam generator[J].Bull JSME, 1970, 13(66):1485-1495.
[8] AHMEd M, ELSAYED C, RAYA K, et al.Investigation of flow boiling heat transfer inside small diameter helically coiled tubes[J].International Journal of Refrigeration, 2012, 35(8):2179-2187.
[9] ZHAO L, GUO L J, BAI B F, et al.Convective boiling heat transfer and two-phase flow characteristics inside a small horizontal helically coiled tubing once-through steam generator[J].International Journal of Heat and Mass Transfer, 2003, 46(25):4779-4788.
[10] 邵莉,刘利民,苑伟,等.R134a卧式螺旋管内沸腾两相流型与传热特性实验研究[J].原子能科学技术,2013,47(3):391-396.SHAO Li, LIU Limin, YUAN Wei, et al.Study two-phase patterns and heat transfer of R134a in horizontal helically coiled tube[J].Atomic Energy Science and Technology, 2013, 47(3):391-396.
[11] CHEN J.A correlation for boiling heat transfer to saturated fluids in convective flow[J].I ＆ EC Process Design and Development, 1966, 5(3):322-329.
[12] 邵莉,许之初,韩吉田,等.卧式螺旋管内R134a沸腾两相传热特性实验研究[J].中国电机工程学报,2011,31(8): 62-66.SHAO Li, XU Zhichu, HAN Jitian, et al.Experimental investigations on two-phase flow boiling heat transfer of R134a in helically coiled tube[J].Proceedings of the CSEE, 2011, 31(8):62-66.
[13] GUNGOR K E, WINTERTON R H S.Simplified general correlation for saturated flow boiling and comparisons of correlations with data[J].Chemical Engineering Research and Design, 1987, 65(2):148-156.
[14] CUI W Z, LI L J, XIN M D.A heat transfer correlation of flow boiling in helically coiled tube[J].International Journal of Heat and Mass Transfer, 2006, 49(17-18):2851-2858.
[15] KLIMENKO V V.A generalized correlation for two phase forced flow heat transfer[J].International Journal of Heat and Mass Transfer, 1988, 31(3):541-552.
[16] COLLIER J G.Convective coiling and condensation[C]// 2nd Bdn Mc Graw-Hil.New York:Oxford Press, 1982:211-214.
[17] WBALLEY P B.Boiling,condesatian and gas-liquid flow[M].Oxford:Ciarendon Press, 1987.
[18] LIU Z, WINTERTON R H S.A general correlation for saturated and subcooled flow boiling in tubes and annuli, based on a nucleate pool boiling equation[J].International Journal of Heat and Mass Transfer, 1991, 34(11):2759-2766.
[19] SEBAN R A, MCLAUGHLIN E F.Heat transfer in tube coils with laminar and turbulent flow[J].International Journal of Heat and Mass Transfer, 1963, 6(5):387-390.
[20] COOPER M G.Heat flow rates in saturated nucleate pool boiling—a wide ranging examination using reduced properties[J].Advance Heat Transfer, 1984, 16(3):157-239.
[1] TIAN Tao, JIANG Kun, CAO Junteng, GUO Chunsheng. Mechanism and properties of slotted metallic nickel foam in flow boiling [J]. Journal of Shandong University(Engineering Science), 2025, 55(6): 58-68.
[2] WANG Xiaopeng, ZHANG Zhiqiang, ZHAO Hongxia, BAI Chao, CHENG Yiguang, GAO Chenchen, LI Guangpeng. Modeling on icing process of large direct cooling ice maker [J]. Journal of Shandong University(Engineering Science), 2025, 55(6): 83-89.
[3] SONG Yunfei, ZHANG Hongxing, ZHOU Yupeng, YANG Changpeng, XIE Yongqi. Design and experimental research of centrifugally-enhanced involute heat pipe for spacecraft [J]. Journal of Shandong University(Engineering Science), 2025, 55(6): 100-107.
[4] Wenjing DU,Junzhe ZHAO,Lixin ZHANG,Zhan WANG,Wanxiang JI. Review and prospect of the development of heat exchanger structure [J]. Journal of Shandong University(Engineering Science), 2021, 51(5): 76-83.
[5] YAN Jiqing, WANG Xiaojia, TIAN Maocheng. Condensation heat transfer characteristics of steam containing non-condensable gas on sawtooth surface [J]. Journal of Shandong University(Engineering Science), 2020, 50(6): 129-134.
[6] Xinchen ZHOU,Xuelai ZHANG,Yue CHEN,Lu LIU. Heat transfer performance analysis of phase change energy storage heat exchanger based on entransy theory [J]. Journal of Shandong University(Engineering Science), 2019, 49(5): 72-84.
[7] WANG Danhua, ZHANG Guanmin, LENG Xueli, XU Mengna, HAN Yuanyuan. The numerical simulation of two-phase flow distribution characteristics in T-tube [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2018, 48(1): 89-95.
[8] LU Guoqiang, HAN Jitian, KONG Lingjian, CHEN Changnian, HU Guiqiu, CHEN Jun, LI Jiangfei. Effect of mass flux on onset of nucleate flow boiling of R134a and tube wall temperature characteristics [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2016, 46(3): 117-122.
[9] GUAN Ning, LUAN Tao, LIU Zhigang, ZHANG Chengwu, JIANG Guilin, QIU Delai. Convective heat transfer in micro pin fin heat sinks with different cross section shapes under variable heating loads [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2016, 46(2): 128-134.
[10] MA Zongzheng, SHAO Fengxiang, WANG Xinli, YANG Anjie. Thermoelectric generator system based on engine exhaust gas [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2016, 46(2): 122-127.
[11] CHEN Changxian, SUN Fengzhong, LI Fei, WU Yanyan. Thermal calculation method for quad-sectional regenerative air preheater [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2014, 44(4): 58-63.
[12] ZHANG Tao, HAN Jitian, YAN Suying, YU Zeting, ZHOU Ran. The analysis and testing of thermal performance on solar evacuated tube [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2014, 44(4): 76-83.
[13] LI Fei, SUN Fengzhong, SHI Yuetao, MA Lei. Experimental research and synergy analysis on characteristics of tube bundles [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2014, 44(4): 70-75.
[14] CHENG Shen, SUN Feng-zhong*. Experimental analysis of condensation heat transfer characteristics under vacuum condition of Nickel based implanted tube bundle [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2014, 44(1): 90-94.
[15] CHE Cui-cui, TIAN Mao-cheng*, LENG Xue-li. Numerical simulations on convective heat transfer characteristics of
 laminar flow with longitudinal vortex induced by winglets [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2013, 43(5): 104-110.
Viewed
Full text


Abstract

Cited
  Shared   
  Discussed   
[1] ZHANG Yong-hua,WANG An-ling,LIU Fu-ping . The reflected phase angle of low frequent inhomogeneous[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2006, 36(2): 22 -25 .
[2] LI Kan . Empolder and implement of the embedded weld control system[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2008, 38(4): 37 -41 .
[3] LAI Xiang . The global domain of attraction for a kind of MKdV equations[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2006, 36(1): 87 -92 .
[4] YU Jia yuan1, TIAN Jin ting1, ZHU Qiang zhong2. Computational intelligence and its application in psychology[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2009, 39(1): 1 -5 .
[5] CHEN Rui, LI Hongwei, TIAN Jing. The relationship between the number of magnetic poles and the bearing capacity of radial magnetic bearing[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2018, 48(2): 81 -85 .
[6] WANG Bo,WANG Ning-sheng . Automatic generation and combinatory optimization of disassembly sequence for mechanical-electric assembly[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2006, 36(2): 52 -57 .
[7] ZHANG Ying,LANG Yongmei,ZHAO Yuxiao,ZHANG Jianda,QIAO Peng,LI Shanping . Research on technique of aerobic granular sludge cultivationby seeding EGSB anaerobic granular sludge[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2006, 36(4): 56 -59 .
[8] Yue Khing Toh1， XIAO Wendong2， XIE Lihua1. Wireless sensor network for distributed target tracking: practices via real test bed development[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2009, 39(1): 50 -56 .
[9] SUN Weiwei， WANG Yuzhen. Finite gain stabilization of singlemachine infinite bus system subject to saturation[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2009, 39(1): 69 -76 .
[10] SUN Yu-li,LI De-fa,ZUO Dun-wen,QI mei . [J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2006, 36(6): 19 -23 .
Copyright 2018 © Editorial office of Journal of Shandong University (Engineering Science)
Supported by Beijing Magtech Co.Ltd