您的位置：山东大学 -> 科技期刊社 -> 《山东大学学报（工学版）》

山东大学学报 (工学版) ›› 2021, Vol. 51 ›› Issue (4): 84-90.doi: 10.6040/j.issn.1672-3961.0.2020.267

• • 上一篇    下一篇

无油双螺杆空压机的运行性能

李鹏1,2,刘兆强1,杨锋苓2,3*,刘欣2   

  1. 1.山东中烟滕州卷烟厂, 山东 滕州 277599;2.山东大学机械工程学院, 山东 济南 250061;3.高效洁净机械制造教育部重点实验室(山东大学), 山东 济南 250061
  • 发布日期:2021-08-18
  • 作者简介:李鹏(1991— ),男,山东滕州人,硕士研究生,主要研究方向为流体机械. E-mail:1591253032@qq.com. *通信作者简介:杨锋苓(1979— ),男,山东莒南人,博士,副教授,主要研究方向为流体机械. E-mail:fly@sdu.edu.cn
  • 基金资助:
    山东省重点研发计划资助项目(2017GGX70101)

Operating characteristics of oil-free twin-screw air compressor

LI Peng1,2, LIU Zhaoqiang1, YANG Fengling2,3*, LIU Xin2   

  1. 1. Tengzhou Cigarette Factory, China Tobacco Shandong Industrial Co., Ltd., Tengzhou 277599, Shandong, China;
    2. School of Mechanical Engineering, Shandong University, Jinan 250061, Shandong, China;
    3. Key Laboratory of High-Efficiency and Clean Mechanical Manufacture of Ministry of Education(Shandong University), Jinan 250061, Shandong, China
  • Published:2021-08-18

PDF (PC)

703

摘要： 为了提高两级压缩无油双螺杆空压机的运行效率,研究两级压缩无油双螺杆空压机的运行特性。采用试验测试和理论推导的方法,研究两级压缩无油双螺杆空压机的多变指数、最佳中间压力、排气温度和排气压力等参数的变化规律。结果表明,空压机的一级压缩多变指数比二级低,两者均高于等熵指数,且随电动机负载率的增加先减小后稳定;将中间冷却器考虑在内后,一级多变指数略高于二级,两者均小于等熵指数,且随电动机负载率的增加略微上升。空压机的最佳中间压力较为复杂,不能简单的认为是压缩后的压力和初始压力乘积的根方。随电动机负载率的增大,一级压缩排气温度逐步下降,二级压缩排气温度逐渐增加,一级排气压力略有下降,二级排气压力略有上升。研究结果为更好的设计和使用无油双螺杆空压机奠定基础。

关键词: 无油双螺杆压缩机, 多变指数, 中间压力, 熵, 热力学

Abstract: In order to improve the operating efficiency of the oil-free twin-screw air compressor, the operating characteristics of the compressor were studied. Polytropic exponent, optimal intermediate pressure, exhausted-air pressure and temperature of the oil-free twin-screw air compressor during the operating processes were systematically studied. The theoretical analyses and experimental measurements were carried out. Results showed that the first-stage compression polytropic index was slightly lower than the second stage, both were higher than the iso-entropy exponent. With the increase of motor load rate, they firstly decreased gradually and then tended to be stabilized. If the intermediate cooler were taken into account, the first-stage compression polytropic index was slightly higher than the second stage. Both were lower than the iso-entropy exponent and increased slightly with the increase in the motor load rate. The optimal intermediate pressure of the oil-free twin-screw air compressor was quite complex, and it could not be simply considered as square root of the product of the compressed and the initial pressure. With the increase in motor load rate, the first-stage compression exhausted-air temperature gradually decreased, the second-stage compression exhausted-air temperature gradually increased, the first-stage exhausted-air pressure slightly decreased and the second-stage exhausted-air pressure slightly increased. Results of this work laid the foundation for better design and use of the oil-free twin-screw air compressor.

Key words: oil-free twin-screw air compressor, polytropic exponent, intermediate pressure, entropy, thermodynamics

中图分类号: 

  • TH138.21
[1] KRICHEL S V, SAWODNY O. Dynamic modeling of compressors illustrated by an oil-flooded twin helical screw compressor[J]. Mechatronics, 2011, 21(1): 77-84.
[2] FERREIRA C A I, ZAMFIRESCU C, ZAYTSEV D. Twin screw oil-free wet compressor for compression-absorption cycle[J]. International Journal of Refrig-eration, 2006, 29(4): 556-565.
[3] SAMBANDAM M T, MADLOOL N A, SAIDUR R, et al. Investigation of energy saving potentials in T-junction and elbow in compressed air systems[J]. Energy Efficiency, 2017, 10(5): 1099-1113.
[4] RANE S, KOVACEVIC A, STOSIC N, et al. Grid deformation strategies for CFD analysis of screw compressors[J]. International Journal of Refrigeration, 2013, 36(7): 1883-1893.
[5] 邢子文,吴华根,束鹏程. 螺杆压缩机设计理论与关键技术的研究和开发[J]. 西安交通大学学报, 2007, 41(7): 755-810. XING Ziwen, WU Huagen, SHU Pengcheng. Research and development on design theory and key technology of screw compressors[J]. Journal of Xi'an Jiaotong University, 2007, 41(7): 755-810.
[6] 王莲芝. 螺杆式空压机机油乳化分析[J]. 城市轨道交通研究, 2012, 15(10): 93-106. WANG Lianzhi. Analysis of the oil emulsification for screw compressor[J]. Urban Mass Transit, 2012, 15(10): 93-106.
[7] 李俊岭,韩志侃. 螺杆式空压机吸气过程技术改造[J]. 化工机械, 2016, 43(1): 125-128. LI Junling, HAN Zhikan. Technical reform of screw type air compressor suction process[J]. Chemical Engineering & Machinery, 2016, 43(1): 125-128.
[8] GUERROTO D, NOURI J M, STOSIC N, et al. Flow measurements in the discharge port of a screw compressor[J]. Process Mechanical Engineering, 2008, 222(4): 201-210.
[9] 金旭,王树刚,张腾飞, 等. 变工况双级压缩中间压力及其对系统性能的影响[J]. 化工学报, 2012, 63(1): 96-102. JIN Xu, WANG Shugang, ZHANG Tengfei, et al. Intermediate pressure and its effect on performance of two-stage compression system with variable operating mode[J]. CIESC Journal, 2012, 63(1): 96-102.
[10] SAIDUR R, RAHIM N A, HASANUZZAMAN M. A review on compressed-air energy use and energy savings[J]. Renewable and Sustainable Energy Reviews, 2010, 14(4): 1135-1153.
[11] CARELLO M, IVANOV A, MAZZA L. Pressure drop in pipe lines for compressed air:comParison between experimental and theoretical analysis[J]. Advances in Fluid Mechanics, 1998, 21: 35-44.
[12] GUO Z G, DENG G Y, CHU P, et al. Evaluation the role of multi-stage compression and waste heat recovery on compressed air energy storage system performance[J]. Applied Mechanics and Materials, 2014, 492(1): 19-23.
[13] SAPMAZ S, KILIC F, EYIDOGAN M, et al. Selection of compressors for petrochemical industry in terms of reliability, energy consumption and maintenance costs examining different scenarios[J]. Energy Exploration & Exploitation, 2015, 33(1): 43-62.
[14] VALENTI G, MURGIA S, CONTALDI G, et al. Experimental evidence of the thermal effect of lubricating oil sprayed in sliding-vane air compressors[J]. Case Studies in Thermal Engineering, 2014, 4: 113-117.
[15] QIN J, LI W, DENG C. Parameters selection and profile calculation for screw rotor of twin screw air compressor[J]. Applied Mechanics and Materials, 2017, 873: 308-313.
[16] LIN W Q, KONG D W, CAI M L. Research on energy consumption of screw compressor under load/unload[J]. Applied Mechanics and Materials, 2011(84/85): 733-738.
[17] 方达宪,张红亚,王艳华. 流体力学[M]. 武汉: 武汉大学出版社, 2018: 227.
[18] 朱明善,林兆庄,刘颖,等. 工程热力学[M]. 北京: 清华大学出版社, 1995: 91-92.
[19] 孙家枢,郝荣亮,钟志勇. 热喷涂科学与技术[M]. 北京:冶金工业出版社, 2013: 28-30.
[20] 张益波,任佳,潘海鹏,等. 一类热定型机换热器的动态建模方法[J]. 化工学报, 2011, 62(8): 2360-2366. ZHANG Yibo, REN Jia, PAN Haipeng, et al. A kind of dynamic modeling method for heat-exchangers of heat-setting machine[J]. CIESC Journal, 2011, 62(8): 2360-2366.
[21] 陈更林,李德玉. 流体力学与流体机械[M]. 徐州: 中国矿业大学出版社, 2012: 330.
[22] 张良,许思传,万玉. PEM燃料电池用空压机多参数多目标优化[J]. 电源技术, 2016, 40(1): 81-83. ZHANG Liang, XU Sichuan, WAN Yu. Multi-objective and multi-parameter optimization for centrifugal compressor used in PEM fuel cells[J]. Power Technology, 2016, 40(1): 81-83.
[23] 王刚华,柏劲松,孙承纬, 等. 准等熵压缩流场反演技术研究[J]. 高压物理学报, 2008, 22(2): 149-152. WANG Ganghua, BAI Jinsong, SUN Chengwei, et al. Backward integration method for tracing isentropic compression field[J]. Chinese Journal of High Pressure Physics, 2008, 22(2): 149-152.
[24] 徐晓明,陈德泉,杨恒,等. 通用机械设备与系统运行及节能[M]. 上海: 同济大学出版社, 2012: 28-29.
[1] 曹芙波,肖胜先,王晨霞,郜德龙,李敦,苏天,秦士杰,王宇飞. 基于熵权TOPSIS的再生砖混水稳材料多指标综合性能评价[J]. 山东大学学报 (工学版), 2025, 55(6): 151-162.
[2] 李长城,罗燕婷,王东宏,康海鹏,潘松. 考虑初始故障状态和继发故障风险的关键线路辨识方法[J]. 山东大学学报 (工学版), 2025, 55(5): 40-50.
[3] 梁涛,刘亚祥,杨硕,徐越,王庆松. 山东省综合能源系统可持续发展能力评价[J]. 山东大学学报 (工学版), 2024, 54(4): 159-168.
[4] 宋辉,张轶哲,张功萱,孟元. 基于类权重和最小化预测熵的测试时集成方法[J]. 山东大学学报 (工学版), 2024, 54(3): 36-43.
[5] 陈宝国,邓明,陈金林. 基于权重邻域熵的数值型信息系统属性约简算法[J]. 山东大学学报 (工学版), 2024, 54(1): 33-44.
[6] 庄绪彩,孙希滕,张宁,田源,殷敬敬,宋修广. 基于主客观组合赋权评价技术的雷视一体机安装方案优选[J]. 山东大学学报 (工学版), 2023, 53(4): 37-47.
[7] 郭茂林,包崇明,周丽华,丁涛,孔兵. 基于TOPSIS的异质网络影响力最大化[J]. 山东大学学报 (工学版), 2022, 52(2): 31-40.
[8] 葛维春,李昭,赵东,李振宇,叶青,傅予,于娜. 含电极式电锅炉的地区电网电源侧综合效益分析[J]. 山东大学学报 (工学版), 2020, 50(5): 90-98.
[9] 程森. 基于熵值法的水利施工企业绩效考核KPI设计方法[J]. 山东大学学报 (工学版), 2020, 50(4): 80-84.
[10] 黄劲潮. 深度残差特征与熵能量优化运动目标跟踪算法[J]. 山东大学学报 (工学版), 2019, 49(4): 14-23.
[11] 陈红,杨小飞,万青,马盈仓. 基于相关熵和流形学习的多标签特征选择算法[J]. 山东大学学报 (工学版), 2018, 48(6): 27-36.
[12] 邱路,叶银忠,姜春娣. 基于小波奇异熵和SOM神经网络的微电网系统故障诊断[J]. 山东大学学报(工学版), 2017, 47(5): 118-122.
[13] 吴建萍,姜斌,刘剑慰. 基于小波包信息熵和小波神经网络的异步电机故障诊断[J]. 山东大学学报(工学版), 2017, 47(5): 223-228.
[14] 林耀进,张佳,林梦雷,王娟. 一种基于模糊信息熵的协同过滤推荐方法[J]. 山东大学学报(工学版), 2016, 46(5): 13-20.
[15] 张佳,林耀进,林梦雷,刘景华,李慧宗. 基于信息熵的协同过滤算法[J]. 山东大学学报(工学版), 2016, 46(2): 43-50.
Viewed
Full text


Abstract

Cited
  Shared   
  Discussed   
[1] 张永花,王安玲,刘福平 . 低频非均匀电磁波在导电界面的反射相角[J]. 山东大学学报(工学版), 2006, 36(2): 22 -25 .
[2] 李 侃 . 嵌入式相贯线焊接控制系统开发与实现[J]. 山东大学学报(工学版), 2008, 38(4): 37 -41 .
[3] 孔祥臻,刘延俊,王勇,赵秀华 . 气动比例阀的死区补偿与仿真[J]. 山东大学学报(工学版), 2006, 36(1): 99 -102 .
[4] 来翔 . 用胞映射方法讨论一类MKdV方程[J]. 山东大学学报(工学版), 2006, 36(1): 87 -92 .
[5] 余嘉元1 , 田金亭1 , 朱强忠2 . 计算智能在心理学中的应用[J]. 山东大学学报(工学版), 2009, 39(1): 1 -5 .
[6] 陈瑞,李红伟,田靖. 磁极数对径向磁轴承承载力的影响[J]. 山东大学学报(工学版), 2018, 48(2): 81 -85 .
[7] 王波,王宁生 . 机电装配体拆卸序列的自动生成及组合优化[J]. 山东大学学报(工学版), 2006, 36(2): 52 -57 .
[8] 季涛,高旭,孙同景,薛永端,徐丙垠 . 铁路10 kV自闭/贯通线路故障行波特征分析[J]. 山东大学学报(工学版), 2006, 36(2): 111 -116 .
[9] 秦通,孙丰荣*,王丽梅,王庆浩,李新彩. 基于极大圆盘引导的形状插值实现三维表面重建[J]. 山东大学学报(工学版), 2010, 40(3): 1 -5 .
[10] 张英,郎咏梅,赵玉晓,张鉴达,乔鹏,李善评 . 由EGSB厌氧颗粒污泥培养好氧颗粒污泥的工艺探讨[J]. 山东大学学报(工学版), 2006, 36(4): 56 -59 .
版权所有 © 2018 《山东大学学报(工学版)》编辑部　
地址: 济南市山大南路27号（250100）　 电话: 0531-88366735　 E-mail: xbgxb@sdu.edu.cn
本系统由北京玛格泰克科技发展有限公司设计开发