基于光滑有限元法的体积锁定研究

山东大学学报(工学版) ›› 2012, Vol. 42 ›› Issue (3): 93-99.

基于光滑有限元法的体积锁定研究

王建明¹,张刚^1*,戚放²,樊现行¹,余丰¹

1. 山东大学机械工程学院, 山东济南 250061; 2. 山东球墨铸铁管公司, 山东济南 250101

收稿日期:2012-01-12 出版日期:2012-06-20 发布日期:2012-01-12
通讯作者: 张刚(1987- ),男,山东滨州人,硕士研究生,主要研究方向为CAE理论及应用. E-mail: gangh727@163.com E-mail:gangh727@163.com
作者简介:王建明(1962- ),男,山东济南人,教授,主要研究方向为计算力学,多体系统动力学. E-mail: wangjianming@sdu.edu.cn
基金资助:
山东省自然科学基金资助项目(Y2007A07)

Study of volumetric locking based on the smoothed finite element method

WANG Jian-ming¹, ZHANG Gang^1*, QI Fang², FAN Xian-hang¹, YU Feng¹

1. School of Mechanical Engineering, Shandong University, Jinan 250061, China;
2. Shandong Ducitile Cast Iron Pipe Co. Ltd., Jinan 250101, China

Received:2012-01-12 Online:2012-06-20 Published:2012-01-12

摘要/Abstract

摘要：

针对数值模拟中求解几乎不可压缩材料时产生的体积锁定问题,提出了2种基于光滑有限元法的解决方案。方案1基于光滑子单元域有限元法,通过将材料特性矩阵划分为剪切部分和挤压部分,利用选择积分分别形成相应的刚度矩阵,对产生体积锁定的挤压部分运用一个光滑子单元进行计算,而对剪切部分运用多个光滑子单元进行计算;方案2综合应用光滑节点域有限元法和光滑边域有限元法,用免于体积锁定的光滑节点域有限元法计算挤压部分,用结果精确的光滑边域有限元法计算剪切部分。算例研究结果证明了2种方案的正确性和有效性,且方案2的计算精度高于光滑节点域有限元法。

关键词: 光滑有限元法, 体积锁定, 选择积分

Abstract:

Aimed at the volumetric locking problems that were produced by the calculation of the nearly incompressible material in numerical simulation, two schemes based on the smoothed finite element method (SFEM) were proposed. The first scheme was to decompose the material properties matrix into two parts, the volumetric part and nonvolumetric part, and the stiffness matrix was also correspondingly decomposed into two parts. Then, the cellbased smoothed finite element method (CS-FEM) using one subcell (SC=1) was used only on the volume-part and the CS-FEM using more than one subcell (SC>1) was used on the remaining part. The second scheme was to use the node-based smoothed finite element method (NS-FEM) that was free from volumetric locking to calculate the volumetric part and to use the edge-based finite element method (ES-FEM) that had accurate results to calculate the remaining part. Results of the numerical study showed that both schemes were correct and effective,and the second scheme was more accurate than NS-FEM.

Key words: smoothed finite element method (SFEM), volumetric locking, selective integration

王建明1,张刚1*,戚放2,樊现行1,余丰1. 基于光滑有限元法的体积锁定研究[J]. 山东大学学报(工学版), 2012, 42(3): 93-99.

WANG Jian-ming1, ZHANG Gang1*, QI Fang2, FAN Xian-hang1, YU Feng1. Study of volumetric locking based on the smoothed finite element method[J]. JOURNAL OF SHANDONG UNIVERSITY (ENGINEERING SCIENCE), 2012, 42(3): 93-99.

参考文献

多维度评价

Viewed

Full text

Abstract

Cited

Shared

Discussed

本文评价

推荐阅读 10

[1]	王素玉,艾兴,赵军,李作丽,刘增文 . 高速立铣3Cr2Mo模具钢切削力建模及预测[J]. 山东大学学报(工学版), 2006, 36(1): 1 -5 .
[2]	李侃 . 嵌入式相贯线焊接控制系统开发与实现[J]. 山东大学学报(工学版), 2008, 38(4): 37 -41 .
[3]	孔祥臻,刘延俊,王勇,赵秀华 . 气动比例阀的死区补偿与仿真[J]. 山东大学学报(工学版), 2006, 36(1): 99 -102 .
[4]	来翔 . 用胞映射方法讨论一类MKdV方程[J]. 山东大学学报(工学版), 2006, 36(1): 87 -92 .
[5]	余嘉元1 , 田金亭1 , 朱强忠2 . 计算智能在心理学中的应用[J]. 山东大学学报(工学版), 2009, 39(1): 1 -5 .
[6]	陈瑞,李红伟,田靖. 磁极数对径向磁轴承承载力的影响[J]. 山东大学学报(工学版), 2018, 48(2): 81 -85 .
[7]	王波,王宁生 . 机电装配体拆卸序列的自动生成及组合优化[J]. 山东大学学报(工学版), 2006, 36(2): 52 -57 .
[8]	李可,刘常春,李同磊 . 一种改进的最大互信息医学图像配准算法[J]. 山东大学学报(工学版), 2006, 36(2): 107 -110 .
[9]	季涛,高旭,孙同景,薛永端,徐丙垠 . 铁路10 kV自闭/贯通线路故障行波特征分析[J]. 山东大学学报(工学版), 2006, 36(2): 111 -116 .
[10]	浦剑1 ,张军平1 ，黄华2 . 超分辨率算法研究综述[J]. 山东大学学报(工学版), 2009, 39(1): 27 -32 .